The UAP-AC-M-PRO supports wireless adoption into your UniFi Wi-Fi network. This feature requires a currently managed UniFi AP operating with the following configuration: The UniFi AP must be running firmware 3.7.7 or newer. UAP-AC-PRO Wireless Security WEP, WPA-PSK, WPA-Enterprise (WPA/WPA2, TKIP/AES) Mounting Wall/Ceiling (Kits Included) Operating Temperature -10 to 70° C (14 to 158° F) Operating Humidity 5 to 95% Noncondensing Certifications CE, FCC, IC. Included with the single-pack of the UAP-AC-PRO Safety Notices 1. Page 35: Limited Warranty 3.

• See Full List On Dl.ubnt.com
• Uap 158 - The Challenge Mac Os Download
• Uap 158 - The Challenge Mac Os Catalina
• Uap 158 - The Challenge Mac Os X

* Included only in the single-pack of the UAP-AC-M

• Wall-mounting: Drill and 6 mm drill bit
• Phillips screwdriver
• Shielded Category 5 (or above) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE.

  We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable

• Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the UAP-AC-M and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground.

Diagram Showing Use of Ethernet Surge Protectors

System Requirements

• Linux, Mac OS X, or Microsoft Windows 7/8/10
• Java Runtime Environment 1.7 (1.8 or newer recommended)
• Web Browser: Google Chrome (Other browsers may have limited functionality)
• UniFi Controller software v5.4 or newer (available at: ui.com/download/unifi)

Wireless Adoption Requirements

The UAP-AC-M supports wireless adoption into your UniFi Wi-Fi network. This feature requires a currently managed UniFi AP operating with the following configuration:

See Full List On Dl.ubnt.com

• The UniFi AP must be running firmware v3.7.7 or newer
• At least one SSID enabled and operating on 5 GHz band
• The UAP-AC-M must be within wireless range of the UniFi AP

LED

Ports

The UniFi AP can be mounted on a wall, pole, or fast-mount of a Ubiquiti high-gain antenna. Perform the steps for the appropriate installation:

Wall Mount

Pole Mount

The included Fast-Mount Adapter allows the UniFi AP to be mounted on a Ubiquiti high-gain antenna equipped with a fast-mount radio mounting bracket.

1. Ensure the Rubber Gaskets remain in place.

Uap 158 - The Challenge Mac Os Download

OR

See “Wireless Adoption Requirements”before proceeding.

1. Ensure the UniFi AP is powered on, and then launch the UniFi Controller software.
2. Go to the Devices page, and the UAP-AC-M will show up as Pending Adoption (Wireless).
3. Click Adopt.

For information on configuring and using the UniFi Controller software, refer to the User Guide located on our website: ui.com/download/unifi

This device must be professionally installed and it is the professional installer’s responsibility to make sure the device is operated within local country regulatory requirements.

Antenna

Select your antenna from the list. Transmit output power is automatically adjusted to comply with the regulations of the applicable country. For a Custom antenna, Antenna Gain is entered manually. Note the requirements and antenna types listed below.

Certified Antenna Types

This radio transmitter FCC ID: SWX-UAPACM / IC: 6545A-UAPACM has been approved by FCC / ISED Canada to operate with the antenna types listed below with the maximum permissible gain for each antenna type indicated. Antenna types not included in this list or having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Uap 158 - The Challenge Mac Os Catalina

* Antenna Model UMA-D (sold separately).

Uap 158 - The Challenge Mac Os X

Antenna Gain